GO BACK TO POWERBAR PAGE 1
  

MULTIPLE PORT POWER BARSTM

Catalog #

Description
PB1020E4 1/0-2/0 AWG 3 Cable ports - 1/2" Bolts
PB1020F4 1/0-2/0 AWG 4 Cable ports - 1/2" Bolts
PB1020G4 1/0-2/0 AWG 5 Cable ports - 1/2" Bolts
PB1020H4 1/0-2/0 AWG 6 Cable ports - 1/2" Bolts
PB3040E4 3/0-4/0 AWG 3 Cable ports - 1/2" Bolts
PB3040F4 3/0-4/0 AWG 4 Cable ports - 1/2" Bolts
PB3040G4 3/0-4/0 AWG 5 Cable ports - 1/2" Bolts
PB3040H4 3/0-4/0 AWG 6 Cable ports - 1/2" Bolts
PB2530E4 250-300 MCM 3 Cable ports - 1/2" Bolts
PB2530F4 250-300 MCM 4 Cable ports - 1/2" Bolts
PB2530G4 250-300 MCM 5 Cable ports - 1/2" Bolts
PB2530H4 250-300 MCM 6 Cable ports - 1/2" Bolts
PB3540E4 350-400 MCM 3 Cable ports - 1/2" Bolts
PB3540F4 350-400 MCM 4 Cable ports - 1/2" Bolts
PB3540G4 350-400 MCM 5 Cable ports - 1/2" Bolts
PB3540H4 350-400 MCM 6 Cable ports - 1/2" Bolts
PB5060E4 500-600 MCM 3 Cable ports - 1/2" Bolts
PB5060F4 500-600 MCM 4 Cable ports - 1/2" Bolts
PB5060G4 500-600 MCM 5 Cable ports - 1/2" Bolts
PB5060H4 500-600 MCM 6 Cable ports - 1/2" Bolts
PB7050E4 700-750 MCM 3 Cable ports - 1/2" Bolts
PB7050F4 700-750 MCM 4 Cable ports - 1/2" Bolts
PB7050G4 700-750 MCM 5 Cable ports - 1/2" Bolts
PB7050H4 700-750 MCM 6 Cable ports - 1/2" Bolts
PB8010E4 800-1000 MCM 3 Cable ports - 1/2" Bolts AL Only †  
PB8010F4 800-1000 MCM 4 Cable ports - 1/2" Bolts AL Only †
PB8010G4 800-1000 MCM 5 Cable ports - 1/2" Bolts AL Only †
PB8010H4 800-1000 MCM 6 Cable ports - 1/2" Bolts AL Only †
PB1000E4 800-1000 MCM 3 Cable ports - 1/2" Bolts AL/CU **
PB1000F4 800-1000 MCM 4 Cable ports - 1/2" Bolts AL/CU **
PB1000G4 800-1000 MCM 5 Cable ports - 1/2" Bolts AL/CU **
PB1000H4 800-1000 MCM 6 Cable ports - 1/2" Bolts AL/CU **
For installations requiring more than 6 cable terminations per Power Bar, please consult Gulf Connectors, Inc. engineers at 239-657-2986.  

† For use on Aluminum cables only
** Utilizes larger Cytolok to accommodate copper conductor to NEMA 1.75" width standard
  
Power Bars will be shipped from the factory in protective shrink-wrap packaging with male tangs fixed in the open position, complete with mounting hardware. All Power Bars are universal and can be mounted on either the right or left side of the spade and in a back-to-back configuration. Hole spacing will be standard NEMA pattern.

Mounting hardware includes:

• Carriage bolts, with nuts and washers for closing down the Cytolok onto the cables (these will be captive to prevent loosening during shipment).

• Two Bellville washers with nuts and bolts for mounting the Power Bar to the top side of the spade.

• Two long bolts and washers to be used for closing down the Cytolok while connecting the Power Bar to the spade. These two bolts will be fastened using our unique, extension nuts, which will allow the use of shorter bolts.

Simply mount the Power Bar to the spade using the top two holes and the Bellville washers. If you're mounting two Power Bars on the same spade in a back-to-back configuration then you can mount them both at the same time with the bolts passing thru the spade. Inserting the cables into a Power Bar™ is much easier and a lot faster then using compression lugs and heavy tools. Simply insert the stripped cable into the Cytolok with one hand and tighten the nut with the other hand. Please note: In a back-to-back installation, the two long bolts will be used in the first two rear positions along with the special extension nuts. These bolts will pass thru the spade and close both the left and right Cytoloks at the same time.

 
Typical back to back Power Bar installation.